FTTH

When do I need a power meter for FTTH, and when do I need an OTDR?

During the installation, acceptance testing, or troubleshooting of an FTTH connection, power meters and OTDR s are used for different tasks. An optical power meter (OPM) measures how much optical power arrives at a specific measurement point. An OTDR (Optical Time Domain Reflectometer), on the other hand, analyzes the fiber-optic link and can identify where a fault or abnormal attenuation is located. In simple terms, the difference can therefore be boiled down to two questions: Power meter: How much optical power is arriving? OFL/OTDR: Where along the fiber-optic link is the problem? Both measurement methods complement each other: If the power measurement indicates an abnormal value, a reflectometric measurement using an OFL or OTDR can then be used to pinpoint the cause.

OTDR-Measurement curve of a fiber-optic link with splices, connectors, macro-bends and fiber ends at 1310 nm and 1650 nm

When do I need a power meter for FTTH?

An optical power meter is used to measure the optical signal level at a specific point along the fiber-optic connection. This allows you to verify, for example, whether sufficient optical power is reaching the subscriber’s connection.

For an active GPON or XGS-PON connection, a selective or filtered PON power meter is particularly useful. GPON uses 1490 nm for the downstream and 1310 nm for the upstream, while XGS-PON uses 1577 nm and 1270 nm, respectively. If multiple signals are transmitted simultaneously over the same fiber, the individual wavelengths must be measured separately.

In such cases, a simple overall level measurement is not sufficient for an accurate assessment. A selective power meter can measure the individual wavelengths separately and thus determine the respective optical levels.

When do I need an OTDR for FTTH?

For example, if the level measurement indicates excessive attenuation, this does not reveal where along the fiber-optic link the cause lies. This is where an OTDR comes into play.

An OTDR sends a defined optical pulse into the fiber and analyzes the backscattered and reflected signal components. This allows events along the fiber-optic link to be detected and localized.

Depending on the measurement, the following events and characteristics of the fiber-optic link, among others, can be identified and analyzed:

  • Link length and fiber end
  • Connectors
  • Splices
  • Bends
  • Attenuation events
  • Reflections
OTDR-Messkurve einer Glasfaserstrecke mit Spleißen, Steckverbindern, Makrobiegung und Faserende bei 1310 nm und 1650 nm
OTDR measurement curve of a fiber-optic link with splices, connectors, a macro-bend, and a fiber end at 1310 nm and 1650 nm

In this way, the OTDR not only answers the question of whether a problem exists, but also provides information about where on the fiber it is located and what might be causing it.

How does troubleshooting work for an FTTH connection?

This results in a simple troubleshooting process:

Faser inspizieren → PON-Pegel messen → Pegel bewerten → bei auffälligem Ergebnis OFL/OTDR einsetzen → Fehler lokalisieren
Inspect the fiber → Measure PON levels → Evaluate the levels → If results are abnormal, use an OFL or OTDR → Locate the fault

Power meters and OTDR s are not competing measurement methods. They answer different questions and can build on each other during troubleshooting.

What is the difference between an OFL and an OTDR?

The full measurement and analysis capabilities of an OTDR are not required for every service call. An Optical Fault Locator (OFL) can be used for rapid fault localization.

OFLs and OTDR s are based on reflectometric measurements but serve different purposes. An OFL narrows the measurement down to the information critical for the service call and guides the technician—as automatically as possible—to an anomalous event. Detected events and their locations are displayed in an easy-to-understand format.

A full-featured OTDR, on the other hand, provides detailed information about the entire fiber run and enables a more in-depth analysis of attenuation, reflections, splices, and connectors.

OFL or OTDR—which method is best suited for what?

Question / ApplicationOFL / Simplified Fault LocationFull-featured OTDR
What do I want to know?Where is an anomalous event located?What is happening in detail along the entire fiber-optic link?
Typical UserInstallation and service techniciansFiber-optic technician / Measurement expert
OperationGuided, largely automated evaluationAutomatic or detailed manual analysis
DisplayEvents and distance presented in an easy-to-understand formatEvent table and complete OTDR curve
Locating faultsYesYes
Detailed characterization of splices and connectorsLimitedYes
Determine event attenuationLimitedYes
Analyze path attenuationLimitedYes
ORL / Reflection AnalysisLimitedYes
Manual detailed analysisNot a primary objectiveYes
Focus of useRapid troubleshooting on the last mileComprehensive acceptance testing and detailed fiber diagnostics
Key advantageFast, clear service assessmentMaximum measurement and analysis depth

Which ARGUS testers are suitable for power meter, OFL, and OTDR measurements?

Depending on the application, various ARGUS testers are available for measurement and fault location. The ARGUS F200 and ARGUS F240 can combine PON measurement functions with the Optical Fault Locator (OFL) for simplified fault location. The ARGUS F300 and ARGUS 300 combine PON measurement functions with a full-featured OTDR.

This allows for immediate fault location or detailed fiber analysis following an abnormal signal level reading, without having to switch to a separate measuring device for the next measurement.

Technical Specifications of the ARGUS OTDR

SpecificationsARGUS OTDR
Measurement MethodOptical Time Domain Reflectometer (OTDR)
Wavelengths1310 + 1650 nm or 1310 + 1550 nm
Dynamic Rangeup to 37 dB
Event dead zone0.9 m
Attenuation dead zone3.5 m
PON dead zone≤ 25 m, typically 20 m
Display range250 m to 240 km*
Measurement modesSmart Auto, Expert, Real Time up to 4 Hz
Detected eventsincluding connectors, splices, and bends
Insertion Loss (IL)Yes
Optical Return Loss (ORL)Yes
Macrobend localizationYes, by comparing two wavelengths
Feed fiber can be usedYes

Matching ARGUS products

How do I find out where a fault is located on an active PON?

How do I find out where a fault is located on an active PON?

An optically low signal level at a GPON or XGS-PON port initially indicates only that there is a problem—not where it is located. To perform targeted troubleshooting, the technician must therefore determine at which point along the fiber-optic link the abnormal attenuation…

3 minutes reading time

Is your measurement task not listed?

The ARGUS application specialists will help you choose the right measurement method and equipment.

Nicholas Tix
Ralf Heil
Marvin Schmidt
Nils Wehner
Marco Fuderholz
Lothar Halbe
Michael Vohl