Ethernet

How do I thoroughly test an FTTH connection—from the fiber-optic cable to the Internet?

An FTTH connection can be technically flawless and still not function properly at the customer’s location. For example, a good PON level does not necessarily mean that the ONT registers correctly, that an IP connection is established, or that the subscribed data rate is actually achieved. A comprehensive test should therefore examine the entire connection chain—from the fiber-optic cable through the PON and ONT to the IP connection, the subscribed services, and the customer’s WLAN. This allows you to determine not only whether the connection is working but also at which level a malfunction is occurring.

Inspect the fiber → Measure the PON level → Check the PON ID → Use an OFL/OTDR if necessary → Register or simulate the ONT → Establish an IP connection → Measure performance → Check services → Examine the WLAN → Document the results

How do I test the fiber optic cable and the PON optical level?

The test begins at the physical level. First, the fiber end faces and connectors are inspected and cleaned if necessary. Contamination or damage can cause additional attenuation and reflections.

Next, the relevant optical levels of the GPON or XGS-PON connection are measured. When PON technologies are operated in parallel, the different wavelengths can be measured and evaluated separately using a selective or filtered power meter.

The PON ID can also be used to verify that the intended PON branch is actually being measured.

How can I measure GPON and XGS-PON simultaneously on a single fiber?

What should I do if the PON level is abnormal?

If the optical level is too low or the measurement reveals another anomaly, the cause must be located along the fiber-optic link.

An OFL (Optical Fault Locator) or OTDR (Optical Time Domain Reflectometer) can be used for this purpose. Reflectometric measurement methods can detect events on the fiber and determine their distance from the measuring device. This allows the search to be narrowed down, for example, to a connector, a splice, a bend, or another abnormal section of the fiber.

How do I find out where a fault is located on an active PON?

How do I check the ONT registration?

If the optical layer appears normal, the next step is to test the PON connection. This involves verifying whether the ONT is properly registered with the OLT.

An ONT simulation can assist with troubleshooting by having the tester itself assume the role of an ONT. This allows the registration to be verified independently of the customer’s existing ONT and further narrows down the cause of a malfunction.

For example, this allows you to determine whether the problem lies with the customer’s ONT or its configuration, or on the network side.

How do I test a GPON or XGS-PON connection if the ONT does not register?

How do I check the IP connection?

A successful ONT registration does not automatically mean that a working Internet connection exists.

After registration, therefore, a check is performed to see if an IP connection can be established. Tools such as ping, traceroute, or other IP tests can be used here to verify the connection at the IP level.

Only once this level is functioning can the actual performance of the connection be properly tested.

How do I measure the actual speed of an FTTH connection?

A performance or speed test can be used to determine the actual data throughput achieved over the FTTH connection.

Depending on the measuring device and equipment, tools such as Ookla Speedtest, iperf, and HTTP/FTP downloads and uploads can be used for this purpose. This allows you to verify whether the bandwidth available on the connection matches the expected data rate.

Especially with fast FTTH connections, it is crucial that both the measuring device and the interface used support the data rate being tested.

How do I test Internet, VoIP, and IPTV services?

In addition to the raw data rate, you can also test the services actually being used. Depending on the connection and equipment, these may include, for example:

  • Internet access
  • VoIP
  • IPTV
  • Uploads and downloads

This helps determine whether the basic IP connection is already disrupted or if only a specific service isn’t working as expected.

What if the FTTH connection is working, but the WLAN is slow?

If the connection up to the router or access point is working perfectly, but the customer still isn’t getting the expected speed over WLAN, the local wireless network must also be included in the diagnosis.

A WLAN analysis, for example, can provide insights into the wireless environment, the channels being used, and potential sources of interference.

This helps determine whether the cause actually lies with the FTTH connection or arises further down the line, beyond the fiber-optic connection, within the customer’s local network.

What does a complete FTTH test look like?

The entire testing procedure can be summarized as follows:

Faser inspizieren → PON-Pegel messen → PON-ID prüfen → bei Bedarf OFL/OTDR einsetzen → ONT registrieren bzw. simulieren → IP-Verbindung herstellen → Performance messen → Dienste prüfen → WLAN untersuchen → Ergebnis dokumentieren
Inspect the fiber → Measure PON levels → Check the PON ID → Use an OFL or OTDR if necessary → Register or simulate the ONT → Establish an IP connection → Measure performance → Test services → Examine the WLAN → Document the results

Which ARGUS testers are suitable for a comprehensive FTTH test?

The ARGUS F Series combines—depending on the model and configuration—various measurement and diagnostic functions for FTTH connections. These include, among other things, selective PON level measurements, PON ID, OFL or OTDR, ONT simulation, as well as IP, performance, and service tests.

This allows multiple levels of an FTTH connection to be examined sequentially and the cause of a fault to be systematically narrowed down.

The key question in a comprehensive FTTH test is therefore not just: “Is the fiber-optic cable in good condition?”

But rather: “Does the connection work from the fiber optic cable to the Internet—and if not, at which level is the fault located?”

Matching ARGUS products

How do I find out where a fault is located on an active PON?

How do I find out where a fault is located on an active PON?

An optically low signal level at a GPON or XGS-PON port initially indicates only that there is a problem—not where it is located. To perform targeted troubleshooting, the technician must therefore determine at which point along the fiber-optic link the abnormal attenuation…

3 minutes reading time

Is your measurement task not listed?

The ARGUS application specialists will help you choose the right measurement method and equipment.

Nicholas Tix
Ralf Heil
Marvin Schmidt
Nils Wehner
Marco Fuderholz
Lothar Halbe
Michael Vohl