Fiber-optic cable

How can I measure GPON and XGS-PON simultaneously on a single fiber?

GPON and XGS-PON can be transmitted in parallel over the same fiber optic cable because both technologies use different wavelengths. For the technician, this means that multiple optical signals may be present simultaneously at a single port. To evaluate these correctly, the individual wavelengths must be measured separately. A selective or filtered PON power meter is used for this purpose. It can distinguish between the relevant GPON and XGS-PON wavelengths and measure their optical levels separately.

Selective level measurement from GPON and XGS-PON: The different downstream and upstream wavelengths are measured and displayed separately.

What wavelengths do GPON and XGS-PON use?

GPON and XGS-PON use different wavelengths for downstream and upstream:

TechnologyDownstreamUpstream
GPON1490 nm1310 nm
XGS-PON1577 nm1270 nm

This can lead to mixed operation—where both technologies are transmitted simultaneously over the same fiber—especially during the gradual expansion of existing GPON networks to XGS-PON.

Selektive Pegelmessung von GPON und XGS-PON: Die unterschiedlichen Downstream- und Upstream-Wellenlängen werden getrennt erfasst und angezeigt.
Selective level measurement of GPON and XGS-PON: The different downstream and upstream wavelengths are measured and displayed separately.

Why isn’t a simple power meter sufficient?

A simple broadband power meter measures optical power but cannot specifically distinguish between the simultaneously present PON wavelengths.

A plausible total value therefore does not automatically mean that both the GPON and XGS-PON levels are within the specified range.

A selective or filtered PON power meter, on the other hand, separates the relevant wavelengths and enables their individual measurement and evaluation. This makes it possible, for example, to distinguish which level belongs to the GPON signal and which to the XGS-PON signal.

What is the Through Mode in a PON measurement?

The measurement becomes even more meaningful in Through Mode. In this mode, the measuring device is connected between the PON and the ONT. The connection remains active while the optical signals between the OLT and the ONT are measured.

This allows downstream and upstream signals to be analyzed during active PON operation.

This is particularly relevant for the upstream: While the OLT transmits continuously in the downstream, the individual ONTs transmit in the upstream only within their assigned time slots. The PON power meter must therefore also be able to detect these burst-shaped upstream signals.

Through Mode: Downstream- und Upstream-Pegel von GPON und XGS-PON werden im laufenden PON-Betrieb getrennt gemessen.
Through Mode: Downstream and upstream levels for GPON and XGS-PON are measured separately during live PON operation.

How does the simultaneous measurement of GPON and XGS-PON work?

In simple terms, the measurement process is as follows:

PON anschließen → vorhandene Wellenlängen erfassen → GPON- und XGS-PON-Pegel getrennt messen → bei Bedarf Through Mode einsetzen → Upstream und Downstream bewerten → PON/ONT identifizieren
Connect the PON → Detect available wavelengths → Measure GPON and XGS-PON levels separately → Use Through Mode if necessary → Evaluate upstream and downstream → Identify PON/ONT

This allows the technician not only to confirm the presence of an optical signal but also to evaluate the various PON signals separately.

Which ARGUS testers can measure GPON and XGS-PON?

For parallel measurement of GPON and XGS-PON, the ARGUS F200, ARGUS F240, and ARGUS F300 offer selective PON measurement functions—depending on the specific configuration.

The selective power meter can be connected to an existing PON connection in Through Mode to determine the optical levels of the various downstream and upstream wavelengths. In addition, depending on the configuration, other PON information—such as the PON ID—can be determined, and alien ONTs on the line can be detected.

Matching ARGUS products

How do I find out where a fault is located on an active PON?

How do I find out where a fault is located on an active PON?

An optically low signal level at a GPON or XGS-PON port initially indicates only that there is a problem—not where it is located. To perform targeted troubleshooting, the technician must therefore determine at which point along the fiber-optic link the abnormal attenuation…

3 minutes reading time

Is your measurement task not listed?

The ARGUS application specialists will help you choose the right measurement method and equipment.

Nicholas Tix
Ralf Heil
Marvin Schmidt
Nils Wehner
Marco Fuderholz
Lothar Halbe
Michael Vohl